BFT PHOBOS BT PDF

Page 3 Lasciando inalterate le caratteristiche essenziali del prodotto, la Ditta si riserva di apportare in qualunque momento le modifiche che essa ritiene convenienti per migliorare tecnicamente, costruttivamente e commercialmente il prodotto, senza impegnarsi ad aggiornare la presente pubblicazione. Page 4 The Company reserves the right to make any alterations deemed appropriate for the technical, manufacturing and commercial improvement of the product, while leaving the essential product features unchanged, at any time and without undertaking to update the present publication. Page 11 Lasciando inalterate le caratteristiche essenziali del prodotto, la Ditta si riserva di apportare in qualunque momento le modifiche che essa ritiene convenienti per migliorare tecnicamente, costruttivamente e commercial- mente il prodotto, senza impegnarsi ad aggiornare la presente pubblicazio- PHOBOS Ver. Page 13 EN standard is lower than that When the automation system is disassembled to be reassembled on specified in the EN standard.

Author:Akinolmaran Yot
Country:Tajikistan
Language:English (Spanish)
Genre:Marketing
Published (Last):21 January 2010
Pages:355
PDF File Size:17.12 Mb
ePub File Size:7.56 Mb
ISBN:887-3-85718-547-9
Downloads:1008
Price:Free* [*Free Regsitration Required]
Uploader:Dozragore



Phobos BT is Automation should be installed on a gate which is moving freely. Any issue with the smooth opening of closing of a gate will not be corrected by adding automation. All wiring should be done by a qualified electrician. Read and follow all instructions and safety procedures. Always make adjustments and connections with power supply turned off. Never let anyone play on or walk within the automatic gate area.

Keep all gate controls out of the reach of children. Stand clear of a moving gate and never cross the path of a moving gate. Important Note: This Quick Reference Guide is a complement to the official manual L from component list on page 3 part of the kit and in no circumstances supersedes it. US: , Ph: , Fax: , www. R Ref. Please refer to drawing below. The kit includes 1 or 2 cables J from component list on page 3 of 3. Note: the cables come with a red sleeve on the green wire on one side.

This side is to be connected to the control board. Gate must swing freely throughout its travel. STEP 1 Position the post mounting bracket A from component list on page 3 and gate mounting bracket B from component list on page 3 using the dimensions in the table depending upon the operator used Phobos BT N or Phobos BT NL and depending upon the desired opening angle 90 degrees or degrees.

Secure post bracket A from component list on page 3 by welding or bolting. Secure gate bracket B from component list on page 3 by welding or bolting. Note: Do not mount gate bracket B from component list on page 3 on vertical pickets. Instead, weld a plate or a bar horizontally across several pickets for reinforcement. Install both the gate and post brackets in a position to ensure that the actuator is level. Locate the limit sensors located under the worm drive cover as shown in above Fig.

Position the gate in closed position as shown on top of Fig. Loosen the screw on the limit sensor at the end of the arm as shown in Fig. Slide the limit sensor at the end of the arm until you hear a faint click of the magnet catching and then tighten the screw on the limit sensor.

Loosen the screw of the limit sensor close to the main body of the operator and slide it all the way backwards against the main body. Manually move the gate to its fully open position as shown on top of Fig. Slide the limit sensor nearest to the motor until you hear a faint click of the magnet catching and then tighten the screw on the limit sensor.

Manually move the gate to its fully closed position as shown on top of Fig. Reengage the operator with the provided manual release key part of Kit D from component list on page 3. Secure bracket by welding or bolting.

The closing limit switch must be pulled all the way against the motor. Locate the limit sensors under the worm drive cover as shown in above Fig. Ensure that the power is turned off before attaching and detaching the connectors and that the terminal blocks are correctly aligned when reconnecting.

Strip cable and connect the core wire to terminal 23 and the shield wire to terminal Note: This terminal block is not removable. The connection of the antenna is easier to complete by removing the board from the small black enclosure. Remove jumper wire. Wires not supplied.

DRAGON SLAYER ROB GRICE PDF

BFT PHOBOS BT A motor puertas abatibles

.

KX-TG3600BX MANUAL PDF

Bft Phobos Quickguide

.

HEJRE KATI PDF

BFT PHOBOS BT A25/1 - Kit L

.

Related Articles